Product Description

 

Working principle

The vacuum in dry screw pumps is created through 2 parallel-arranged screw rotors that rotate in opposite directions. These rotors trap the gas coming in through the inlet and deliver it to the gas discharge or pressure side. As the gas is getting compressed, there is no contact between the rotors. This does away with any need for the compression chamber to have any operating fluids or lubrication.
 The lubricant used to lubricate the gears and shaft seal is sealed in the gearbox by the shaft seal. The pump can be cooled either directly by circulating cooling water or by a cooling unit with fan and radiator.
The dry screw vacuum pump adopts a special rotor pitch design, compared with the ordinary rotor pitch design, reduce the energy consumption by about 30%, the temperature rise of the exhaust end is reduced by about 100 ºC, the reliability and stability of the operation of the product is greatly improved, can be suitable for any working conditions of vacuum.
The dry screw pumps can be widely used in solvent recovery, vacuum drying, concentration, crystallization, distillation and other processes in the chemical and pharmaceutical industries, vacuum extrusion and molding in the plastic and rubber industries, vacuum degassing in the metallurgical industry; vacuum degassing and drying in the solar energy, microelectronics, lithium battery and other industries.

Pump body and end caps:  high-strength cast iron.
Pump body and end caps:  high strength cast iron.
Screw rotor:                        ductile cast iron.
Anti-corrosion coating:        corrosion-resistant Hastelloy.
Synchronous gears:            alloy steel.
Radial lip seal:                     imported PTFE mixture or
                                            high-temperature resistant fluorine rubber;
Seal bushings:                    stainless steel surface covered with ceramic.

Flow chart

 

Main features

1. The screw rotor is designed with variable pitch structure, the ultimate vacuum can reach below 1Pa, which can meet all kinds of vacuum processing from atmosphere to high vacuum.
2. Oil free – Adapt to various special working conditions for reliable use.
3. It can operate reliably in the pressure range from atmosphere to several Pa.
4. No friction between moving parts, simple structure, lower operation and maintenance cost.
5. Nitrogen seal and composite seal design is optional, which has the benefit of good reliability, low cost of use, simple maintenance.
6. The rotor is dynamically balanced at high speed and the motor is connected by flange, with high concentricity, low vibration and low noise.
7. Hastelloy anti-corrosion coating is optional for rotor surface, condensable material is not easy to condense in the pump cavity, better corrosion resistance.
8. Compared with oil seal pump, liquid ring pump, there is no waste gas, no waste liquid, no waste oil emission, energy saving and environmental friendly.
It can be used alone or with Roots vacuum pump, air-cooled Roots vacuum pump, molecular vacuum pump, etc. to obtain an oil-free high vacuum system.

The benefit of dry screw vacuum pump compared to liquid ring vacuum pump:

    -Shorten the process cycle and improve production efficiency
    -Reduce water consumption
    -Save energy
    -Improve product quality
    -Can recover solvent by reducing the drying time of products
    -Reduce the cost of wastewater and waste gas treatment

A CASE in a pharmaceutical factory
Process introduction:The penicillin sodium salt solution is fed into the crystallization tank through vacuum. By steam heating, agitator stirring, and adding butanol, the water and butanol in the penicillin solution are pumped into the condenser and condensed into the liquid collecting tank, which can be reused.

Process requirements:
1. The volume of crystallization tank is 7.5m3, and about 4.5m3 penicillin solution is added in the process.
2. Before entering the crystallization tank, the water content of penicillin solution is about 20%, and after crystallization, the water content is required to be about 1%.
3. Vacuum feeding for 2h, then adding butanol for 30min, and then starting to crystallize. The process requires low temperature and fast speed, and the lower the temperature, the better the quality of penicillin. The shorter the reaction time, the better.
4. Vacuum degree requirements: the vacuum degree shall be kept above -0.097MPa. High vacuum degree can reduce the reaction temperature and shorten the reaction time.

The previous vacuum system was 2BE1252+air ejector, which is now transformed into a dry screw vacuum pump. The comparison table of test data is as follows:

vacuum system 2BE1252+ejector DVP 1600 screw pump
Feeding time (h) 2 1.5
Liquid temperature at the beginning of crystallization (ºC) 31.5 16.6
Crystallization time (h) 6 4.5
Time from crystallization to liquid coming out (min) 30 15
Crystal quality average good
Power consumption (KW) 45 37
Water consumption (m3) 26.4 0.72

Economic benefit analysis:

  Cost saving(USD) Remark
Water consumption and treatment 130 Water cost: $0.65/m3, water treatment: 30/m3
Power 15 $0.15/Kwh
Labor, production efficiency 43 Reduced from 6 hour to 4.5 hour
Sum up 188  

Please contact us for a detailed report of economic benefit analysis for your applications! 

 

Configuration
Standard configuration:
Machine base, pump head, coupling, motor, driving screen, air inlet connector, check valve, vacuum gauge, manual filling valve exhaust port muffler.
Optional accessories:
Inlet filter, inlet condenser, solvent flushing device, nitrogen purging device, nitrogen sealing device, exhaust port condenser, solenoid filling valve, cooling water flow switch, temperature sensor, pressure transmitter.

Applications

Leak Detection    Metallurgy  Industrial furnace  Lithium Battery
Chemical, pharmaceutical  Wind tunnel test  Power Industry Vacuum coating
Microelectronics industry Drying Process  Packaging and Printing Solar Energy
Exhaust gas recovery       

Product Parameters

Technical data of Variable pitch Dry screw vacuum pump

                Spec.
Model
Nominal pumping speed(50Hz) Ultimate pressure Nominal motor rating (50Hz)   Nominal motor speed  (50Hz)  Noise level   Lp Maximum
cooling water required
Suction Connection size Discharge Connection size Weight (Without Motor)
 m³/h Pa kw rpm dB(A) L/min mm mm Kg
DVP-180 181 2 4 2900 82 8 50 40 280
DVP-360 354 2 7.5 2900 83 10 50 40 400
DVP-540 535 2 11 2900 83 10 50 40 500
DVP-650 645 1 15 2900 84 20 65 50 600
DVP-800 780 1 22 2900 86 30 100 80 800
DVP-1600 1450 1 37 2900 86 40 125 100 1200

Technical data of Constant pitch Dry screw vacuum pump

                Spec.
Model
Nominal pumping speed(50Hz) Ultimate pressure Nominal motor rating (50Hz)   Nominal motor speed  (50Hz)  Noise level   Lp Maximum
cooling water required
Suction Connection size Discharge Connection size Weight (Without Motor)
 m³/h Pa kw rpm dB(A) L/min mm mm Kg
DSP-140 143 5 4 2900 82 10 50 40 240
DSP-280 278 5 7.5 2900 83 20 50 40 350
DSP-540 521 5 15 2900 83 30 65 50 550
DSP-650 617 5 18.5 2900 84 45 65 50 630
DSP-720 763 5 22 2900 85 55 80 80 780
DSP-1000 912 5 30 2900 86 70 100 80 880

Note: The cooling water volume of the dry screw vacuum pump provided in the table is the amount under 20ºC room temperature water. When the dry screw vacuum pump uses cooling device, the cooling water will be increased, the difference of inlet and outlet water temperature is generally controlled below 7ºC is appropriate.

 

Dimension

 

 

FAQ

Q: What information should I offer for an inquiry?
A: You can inquire based on the model directly, but it is always recommended that you contact us so that we can help you to check if the pump is the most appropriate for your application.

Q: Can you make a customized vacuum pump?
A: Yes, we can do some special designs to meet customer applications. Such as customized sealing systems, speical surface treatment can be applied for roots vacuum pump and screw vacuum pump. Please contact us if you have special requirements. 

Q: I have problems with our vacuum pumps or vacuum systems, can you offer some help?
A: We have application and design engineers with more than 30 years of experience in vacuum applications in different industries and help a lot of customers resolve their problems, such as leakage issues, energy-saving solutions, more environment-friendly vacuum systems, etc. Please contact us and we’ll be very happy if we can offer any help to your vacuum system.

Q: Can you design and make customized vacuum systems?
A: Yes, we are good for this.

Q: What is your MOQ?
A: 1 piece or 1 set.

Q: How about your delivery time?
A: 5-10 working days for the standard vacuum pump if the quantity is below 20 pieces, 20-30 working days for the conventional vacuum system with less than 5 sets. For more quantity or special requirements, please contact us to check the lead time.

Q: What are your payment terms?
A: By T/T, 50% advance payment/deposit and 50% paid before shipment.

Q: How about the warranty?
A: We offer 1-year warranty (except for the wearing parts).

Q: How about the service?
A: We offer remote video technical support. We can send the service engineer to the site for some special requirements.

After-sales Service: Online Video Instruction
Warranty: 1 Year
Suction Connection Size: 100 mm
Cooling Water Required: 30 L/Min
Weight (Without Motor) Approx.: 800 Kg
Pitch Type: Third Generation Variable Pitch

vacuum pump

How Do You Maintain and Troubleshoot Vacuum Pumps?

Maintaining and troubleshooting vacuum pumps is essential to ensure their optimal performance and longevity. Here’s a detailed explanation:

Maintenance of Vacuum Pumps:

1. Regular Inspection: Perform regular visual inspections of the pump to check for any signs of damage, leaks, or abnormal wear. Inspect the motor, belts, couplings, and other components for proper alignment and condition.

2. Lubrication: Follow the manufacturer’s guidelines for lubrication. Some vacuum pumps require regular oil changes or lubrication of moving parts. Ensure that the correct type and amount of lubricant are used.

3. Oil Level Check: Monitor the oil level in oil-sealed pumps and maintain it within the recommended range. Add or replace oil as necessary, following the manufacturer’s instructions.

4. Filter Maintenance: Clean or replace filters regularly to prevent clogging and ensure proper airflow. Clogged filters can impair pump performance and increase energy consumption.

5. Cooling System: If the vacuum pump has a cooling system, inspect it regularly for cleanliness and proper functioning. Clean or replace cooling components as needed to prevent overheating.

6. Seals and Gaskets: Check the seals and gaskets for signs of wear or leakage. Replace any damaged or worn seals promptly to maintain airtightness.

7. Valve Maintenance: If the vacuum pump includes valves, inspect and clean them regularly to ensure proper operation and prevent blockages.

8. Vibration and Noise: Monitor the pump for excessive vibration or unusual noise, which may indicate misalignment, worn bearings, or other mechanical issues. Address these issues promptly to prevent further damage.

Troubleshooting Vacuum Pump Problems:

1. Insufficient Vacuum Level: If the pump is not achieving the desired vacuum level, check for leaks in the system, improper sealing, or worn-out seals. Inspect valves, connections, and seals for leaks and repair or replace as needed.

2. Poor Performance: If the pump is not providing adequate performance, check for clogged filters, insufficient lubrication, or worn-out components. Clean or replace filters, ensure proper lubrication, and replace worn parts as necessary.

3. Overheating: If the pump is overheating, check the cooling system for blockages or insufficient airflow. Clean or replace cooling components and ensure proper ventilation around the pump.

4. Excessive Noise or Vibration: Excessive noise or vibration may indicate misalignment, worn bearings, or other mechanical issues. Inspect and repair or replace damaged or worn parts. Ensure proper alignment and balance of rotating components.

5. Motor Issues: If the pump motor fails to start or operates erratically, check the power supply, electrical connections, and motor components. Test the motor using appropriate electrical testing equipment and consult an electrician or motor specialist if necessary.

6. Excessive Oil Consumption: If the pump is consuming oil at a high rate, check for leaks or other issues that may be causing oil loss. Inspect seals, gaskets, and connections for leaks and repair as needed.

7. Abnormal Odors: Unusual odors, such as a burning smell, may indicate overheating or other mechanical problems. Address the issue promptly and consult a technician if necessary.

8. Manufacturer Guidelines: Always refer to the manufacturer’s guidelines and recommendations for maintenance and troubleshooting specific to your vacuum pump model. Follow the prescribed maintenance schedule and seek professional assistance when needed.

By following proper maintenance procedures and promptly addressing any troubleshooting issues, you can ensure the reliable operation and longevity of your vacuum pump.

vacuum pump

How Do Vacuum Pumps Impact the Quality of 3D Printing?

Vacuum pumps play a significant role in improving the quality and performance of 3D printing processes. Here’s a detailed explanation:

3D printing, also known as additive manufacturing, is a process of creating three-dimensional objects by depositing successive layers of material. Vacuum pumps are utilized in various aspects of 3D printing to enhance the overall quality, accuracy, and reliability of printed parts. Here are some key ways in which vacuum pumps impact 3D printing:

1. Material Handling and Filtration: Vacuum pumps are used in 3D printing systems to handle and control the flow of materials. They create the necessary suction force to transport powdered materials, such as polymers or metal powders, from storage containers to the printing chamber. Vacuum systems also assist in filtering and removing unwanted particles or impurities from the material, ensuring the purity and consistency of the feedstock. This helps to prevent clogging or contamination issues during the printing process.

2. Build Plate Adhesion: Proper adhesion of the printed object to the build plate is crucial for achieving dimensional accuracy and preventing warping or detachment during the printing process. Vacuum pumps are employed to create a vacuum environment or suction force that securely holds the build plate and ensures firm adhesion between the first layer of the printed object and the build surface. This promotes stability and minimizes the risk of layer shifting or deformation during the printing process.

3. Material Drying: Many 3D printing materials, such as filament or powdered polymers, can absorb moisture from the surrounding environment. Moisture-contaminated materials can lead to poor print quality, reduced mechanical properties, or defects in the printed parts. Vacuum pumps with integrated drying capabilities can be employed to create a low-pressure environment, effectively removing moisture from the materials before they are used in the printing process. This ensures the dryness and quality of the materials, resulting in improved print outcomes.

4. Resin Handling in Stereolithography (SLA): In SLA 3D printing, a liquid resin is selectively cured using light sources to create the desired object. Vacuum pumps are utilized to facilitate the resin handling process. They can be employed to degas or remove air bubbles from the liquid resin, ensuring a smooth and bubble-free flow during material dispensing. This helps to prevent defects and imperfections caused by trapped air or bubbles in the final printed part.

5. Enclosure Pressure Control: Some 3D printing processes, such as selective laser sintering (SLS) or binder jetting, require the printing chamber to be maintained at a specific pressure or controlled atmosphere. Vacuum pumps are used to create a controlled low-pressure or vacuum environment within the printing chamber, enabling precise pressure regulation and maintaining the desired conditions for optimal printing results. This control over the printing environment helps to prevent oxidation, improve material flow, and enhance the quality and consistency of printed parts.

6. Post-Processing and Cleaning: Vacuum pumps can also aid in post-processing steps and cleaning of 3D printed parts. For instance, in processes like support material removal or surface finishing, vacuum systems can assist in the removal of residual support structures or excess powder from printed objects. They can also be employed in vacuum-based cleaning methods, such as vapor smoothing, to achieve smoother surface finishes and enhance the aesthetics of the printed parts.

7. System Maintenance and Filtration: Vacuum pumps used in 3D printing systems require regular maintenance and proper filtration to ensure their efficient and reliable operation. Effective filtration systems within the vacuum pumps help to remove any contaminants or particles generated during printing, preventing their circulation and potential deposition on the printed parts. This helps to maintain the cleanliness of the printing environment and minimize the risk of defects or impurities in the final printed objects.

In summary, vacuum pumps have a significant impact on the quality of 3D printing. They contribute to material handling and filtration, build plate adhesion, material drying, resin handling in SLA, enclosure pressure control, post-processing and cleaning, as well as system maintenance and filtration. By utilizing vacuum pumps in these critical areas, 3D printing processes can achieve improved accuracy, dimensional stability, material quality, and overall print quality.

vacuum pump

What Is the Purpose of a Vacuum Pump in an HVAC System?

In an HVAC (Heating, Ventilation, and Air Conditioning) system, a vacuum pump serves a crucial purpose. Here’s a detailed explanation:

The purpose of a vacuum pump in an HVAC system is to remove air and moisture from the refrigerant lines and the system itself. HVAC systems, particularly those that rely on refrigeration, operate under specific pressure and temperature conditions to facilitate the transfer of heat. To ensure optimal performance and efficiency, it is essential to evacuate any non-condensable gases, air, and moisture from the system.

Here are the key reasons why a vacuum pump is used in an HVAC system:

1. Removing Moisture: Moisture can be present within an HVAC system due to various factors, such as system installation, leaks, or improper maintenance. When moisture combines with the refrigerant, it can cause issues like ice formation, reduced system efficiency, and potential damage to system components. A vacuum pump helps remove moisture by creating a low-pressure environment, which causes the moisture to boil and turn into vapor, effectively evacuating it from the system.

2. Eliminating Air and Non-Condensable Gases: Air and non-condensable gases, such as nitrogen or oxygen, can enter an HVAC system during installation, repair, or through leaks. These gases can hinder the refrigeration process, affect heat transfer, and decrease system performance. By using a vacuum pump, technicians can evacuate the air and non-condensable gases, ensuring that the system operates with the designed refrigerant and pressure levels.

3. Preparing for Refrigerant Charging: Prior to charging the HVAC system with refrigerant, it is crucial to create a vacuum to remove any contaminants and ensure the system is clean and ready for optimal refrigerant circulation. By evacuating the system with a vacuum pump, technicians ensure that the refrigerant enters a clean and controlled environment, reducing the risk of system malfunctions and improving overall efficiency.

4. Leak Detection: Vacuum pumps are also used in HVAC systems for leak detection purposes. After evacuating the system, technicians can monitor the pressure to check if it holds steady. A significant drop in pressure indicates the presence of leaks, enabling technicians to identify and repair them before charging the system with refrigerant.

In summary, a vacuum pump plays a vital role in an HVAC system by removing moisture, eliminating air and non-condensable gases, preparing the system for refrigerant charging, and aiding in leak detection. These functions help ensure optimal system performance, energy efficiency, and longevity, while also reducing the risk of system malfunctions and damage.

China Good quality 780 M3/H Dvp-800 Variable Pitch Pharmaceutical/Petrochemical Industry Dry Screw Vacuum Pump   vacuum pump oil near me		China Good quality 780 M3/H Dvp-800 Variable Pitch Pharmaceutical/Petrochemical Industry Dry Screw Vacuum Pump   vacuum pump oil near me
editor by CX 2023-10-26